Difference between revisions of "Cosmostreamer for DJI Fly drones"

From Cosmostreamer Wiki
Jump to navigation Jump to search
Line 52: Line 52:
USB-C port on Raspberry Pi 4 is busy by DJI RC-N1 connection, so need to made a custom USB cable with additional part for power.<br>
USB-C port on Raspberry Pi 4 is busy by DJI RC-N1 connection, so need to made a custom USB cable with additional part for power.<br>
[https://cosmostreamer.com/products/djiflydrones/diy/img/usb-c-with-power-cable-rcn1.jpg https://cosmostreamer.com/products/djiflydrones/diy/img/usb-c-with-power-cable-rcn1.jpg]<br>
[https://cosmostreamer.com/products/djiflydrones/diy/img/usb-c-with-power-cable-rcn1.jpg https://cosmostreamer.com/products/djiflydrones/diy/img/usb-c-with-power-cable-rcn1.jpg]<br>
[https://cosmostreamer.com/products/djigoggles2/diy/img/usb-c-power-cable-scheme.jpg https://cosmostreamer.com/products/djigoggles2/diy/img/usb-c-power-cable-scheme-small.jpg]
[https://cosmostreamer.com/products/djiflydrones/diy/img/usb-c-power-cable-scheme-rcn1.jpg https://cosmostreamer.com/products/djiflydrones/diy/img/usb-c-power-cable-scheme-rcn1-small.jpg]
<br><br><br>
<br><br><br>

Revision as of 16:32, 11 December 2023

Product page

http://cosmostreamer.com/products/djiflydrones/

Supported Drones

Any drone which work with DJI Fly application and DJI RC-N1 controller.

DJI RC and DJI RC2 are not supported!
  • DJI Mini 2
  • DJI Mini 3
  • DJI Mini 3 Pro
  • DJI Mavic 3
  • DJI Mavic 3 Pro
  • DJI Air 2S
  • DJI Mavic Air 2




Hardware

Cosmostreamer for DJI Fly drones can work on these boards:



Raspberry Pi 4B

Any RAM size. 1Gb, 2Gb, 4Gb, 8Gb.

  • Two micro-HDMI outs, only one available for video output
  • Analog video out (CVBS, TV-out) in 3.5 mini-jack
  • DSI display may be used. If DSI display connected - video output only on this display.
  • Wi-Fi 2.4/5 GHz
  • Ethernet 10/100/1000 Mbit/s
  • 2 USB 2.0 ports + 2 USB 3.0 ports
  • 1 USB-C port (used for DJI RC-N1 connection)




Installing the Cosmostreamer firmware

  1. Get a blank microSD card of 8GB or larger. Insert the microSD card into the card reader
  2. Download ZIP-archive with firmware content
  3. Extract .img file from downloaded ZIP archive
  4. Use Win32DiskImager on Windows or Balena Etcher on Mac and write .img file on microSD card
  5. Insert the microSD card into the Raspberry Pi
  6. If you have a monitor or a TV with HDMI input - plug it to the Raspberry Pi 4B HDMI-0 port (nearest to USB-C port)
  7. Plug a standard USB power supply or powerbank to the Raspberry Pi (go to chapter Power for Raspberry Pi). Raspberry Pi must start booting. A couple of reboots may be during the first boot process.




Power for Raspberry Pi

For using with DJI RC-N1 Raspberry Pi 4 must be powered ONLY from GPIO or from PoE or via USB-C port with custom cable.


Power with GPIO (pins)

Use any USB cable, need to cut it and connect to the RPI only 2 wires - Red (5V) and Black (Gnd). Then you can use it with any standard USB power supply or powerbank.
rpi-gpio-pwr.jpg


Power with USB-C port

USB-C port on Raspberry Pi 4 is busy by DJI RC-N1 connection, so need to made a custom USB cable with additional part for power.
usb-c-with-power-cable-rcn1.jpg
usb-c-power-cable-scheme-rcn1-small.jpg