CosmoViewerNG for Windows

From Cosmostreamer Wiki
Jump to navigation Jump to search

Main client application for Cosmostreamer NG. Allows to change Cosmostreamer settings, control camera with video stream, etc.

Also CosmoViewerNG for Windows can work with some types of cameras directly with Wi-Fi or USB connection to PC.

Cosmostreamer connection

Connect your PC/laptop to the Wi-Fi network "cosmostreamer", default password is "1234512345" or connect your PC/laptop to the local network with Ethernet cable. Cosmostreamer device must be discovered and shown in list. Click on it for connection.



Direct connection to cameras and other devices

DJI Osmo / Osmo+ / Osmo Pro / Osmo RAW


DJI Pocket Osmo



DJI Pocket 2


DJI Osmo Action



DJI FPV Goggles



DJI Raven Eye


Insta360

Insta360 EVO and Insta360 X2 tested. Other models should also work, but they need to be tested and confirmed.

Insta360 EVO can be connected only with Wi-Fi. Insta360 X2 can be connected with Wi-Fi or with USB cable.

Connection to camera

Wi-Fi connection

Just connect your PC Wi-Fi to Insta360 camera Wi-Fi network. Default password for EVO is 12345678, default password for X2 is 88888888.
Note: be carefull! The password on these Insta360 cameras cannot be changed even in the official app, so any of your neighbors can access your camera and, possible, to your PC if it connected to camera Wi-Fi. Discussion on Reddit

USB connection
  1. Switch USB mode on Insta360 X2 to "Android" (Swipe from up to down on Insta360 X2 display, swipe from right to left, click gears icon, menu "General" -> "USB mode", choose "Android")
  2. Connect your Insta360 X2 to PC with a standard USB-C cable.
  3. In some cases also need to instal WinUSB driver, follow next steps
  4. Download Zadig application
  5. Run Zadig and open menu Settings -> List All Devices
    Zadig-insta360-1.png

  6. Choose "Insta360 ONE" in list and click "Install driver" or "Reinstall driver" button
    Zadig-insta360-2.png


Configuring CosmoViewerNG

  1. Run CosmoViewerNG application on PC
  2. Click "Application settings" icon (3rd icon from bottom in left panel)
  3. Go to chapter "Cameras". Choose "Insta360" in list and click "Save"
    Cosmoviewerng-insta360-1.png

  4. One or more devices should be found in list (the same camera but on diffent network interfaces)
    Cosmoviewerng-insta360-2.png

  5. Click any device (better to use device with address "127.0.0.1") and you should see video if camera already connected. Settings available as "gears" icon in left panel
    Cosmoviewerng-insta360-4.png

  6. In settings change connection type (Wi-Fi or USB)
    Cosmoviewerng-insta360-5.png


Changing preview resolution

Click "Camera settings" icon, tab "Video output". Change resolution in list. Click on "Save" button is not needed

Cosmoviewerng-insta360-7.png


Real-time panorama stitching

NVidia graphics card ONLY (at current moment)

Most important feature - real-time stitching from two fisheyes into equirectangular format. It's strongly needed if you want to stream on Youtube. Unfortunately, Insta360 EVO and X2 does not support onboard stitching. Native Insta360 application can do stitching, but resolution is limited on 1280s. CosmoViewerNG can do stitching in 4K resolution (3840x1920) up to 60 FPS, but powerfull graphics card is needed for encoding stitched video in H264 codec. For example, my GTX 1650 SUPER is well fast for do 4K stitching on 30 FPS with a small latency, but in 60 FPS latency is big.

  1. Click "Camera settings" icon, tab "Stitching"
    Cosmoviewerng-insta360-6.png

  2. Check option "Enable two-fisheyes to equirectangular stitching"
  3. Other params is by default for Insta360 X2 camera, don't change it if you are not sure what you do
  4. "Resize output video" is usefull for Youtube streaming, to correct video resolution
  5. "HW acceleration" strongly recommended. At current moment only NVidia graphics cards are supported.
  6. Click "Save" and you should see video in equirectangular format.

Downloads