Cosmostreamer for DJI Goggles2/Integra - Revision history

Admin at 00:03, 7 May 2026

2026-05-07T00:03:14Z

← Older revision		Revision as of 03:03, 7 May 2026
Line 72:		Line 72:
	<pre style="color: red">Not supported </pre>		<pre style="color: red">Not supported </pre>
	Without a hardware H264 video decoder this is a bad choice for using with Cosmostreamer.		Without a hardware H264 video decoder this is a bad choice for using with Cosmostreamer.
			<br><br>

			==Common connections scheme==
			[[File:Dji-goggles-connection.png\|800px]]
	<br><br>		<br><br>

2026-05-06T23:09:00Z

With two 5V and two Gnd pins

← Older revision		Revision as of 02:09, 7 May 2026
Line 105:		Line 105:
	<br>		<br>
	<pre>5V goes to pins 2 and 4		<pre>5V goes to pins 2 and 4
	~~Gnd~~ goes to pins 6 and 14 (or any other GND pins, check the Raspberry Pi pinout scheme below)</pre>		GND goes to pins 6 and 14 (or any other GND pins, check the Raspberry Pi pinout scheme below)</pre>

	[[File:Rpi4b-power-2.png\|800px]]		[[File:Rpi4b-power-2.png\|800px]]

2026-05-06T23:08:51Z

With one 5V and one Gnd pin

← Older revision		Revision as of 02:08, 7 May 2026
Line 97:		Line 97:
	<br>		<br>
	<pre>5V goes to pin 2		<pre>5V goes to pin 2
	~~Gnd~~ goes to pin 6</pre>		GND goes to pin 6 (or any other GND pin, check the Raspberry Pi pinout scheme below)</pre>
	[[File:Rpi4b-power-1.png\|800px]]		[[File:Rpi4b-power-1.png\|800px]]
	<br>		<br>

2026-05-06T23:08:25Z

With two 5V and two Gnd pins

← Older revision		Revision as of 02:08, 7 May 2026
Line 105:		Line 105:
	<br>		<br>
	<pre>5V goes to pins 2 and 4		<pre>5V goes to pins 2 and 4
	Gnd goes to pins 6 and 14 (or any other GND pins, check ~~Rpi~~ pinout scheme below)</pre>		Gnd goes to pins 6 and 14 (or any other GND pins, check the Raspberry Pi pinout scheme below)</pre>

	[[File:Rpi4b-power-2.png\|800px]]		[[File:Rpi4b-power-2.png\|800px]]

2026-05-06T23:08:08Z

With two 5V and two Gnd pins

← Older revision		Revision as of 02:08, 7 May 2026
Line 105:		Line 105:
	<br>		<br>
	<pre>5V goes to pins 2 and 4		<pre>5V goes to pins 2 and 4
	Gnd goes to pins 6 and 14 (or any other ~~Gnd~~ pins, check pinout below)</pre>		Gnd goes to pins 6 and 14 (or any other GND pins, check Rpi pinout scheme below)</pre>

	[[File:Rpi4b-power-2.png\|800px]]		[[File:Rpi4b-power-2.png\|800px]]

2026-05-06T23:07:49Z

With two 5V and two Gnd pins

← Older revision		Revision as of 02:07, 7 May 2026
Line 104:		Line 104:
	A bit more difficult to connect, but more stable under load. You just need to connect the same wire to two pins. Two pins for 5V and two pins for GND. Recommended wire cross-section: 2.0 mm² or larger.		A bit more difficult to connect, but more stable under load. You just need to connect the same wire to two pins. Two pins for 5V and two pins for GND. Recommended wire cross-section: 2.0 mm² or larger.
	<br>		<br>
			<pre>5V goes to pins 2 and 4
			Gnd goes to pins 6 and 14 (or any other Gnd pins, check pinout below)</pre>

	[[File:Rpi4b-power-2.png\|800px]]		[[File:Rpi4b-power-2.png\|800px]]
	<br><br><br>		<br><br><br>

2026-05-06T23:06:55Z

With one 5V and one Gnd pin

← Older revision		Revision as of 02:06, 7 May 2026
Line 96:		Line 96:
	Minimal variant. But make sure the wires are not too thin, otherwise they may not be able to carry enough current. Recommended wire cross-section: 2.0 mm² or larger.		Minimal variant. But make sure the wires are not too thin, otherwise they may not be able to carry enough current. Recommended wire cross-section: 2.0 mm² or larger.
	<br>		<br>
	<pre>5V goes to pin 2.		<pre>5V goes to pin 2
	Gnd goes to pin 6</pre>		Gnd goes to pin 6</pre>
	[[File:Rpi4b-power-1.png\|800px]]		[[File:Rpi4b-power-1.png\|800px]]

2026-05-06T23:06:45Z

With one 5V and one Gnd pin

← Older revision		Revision as of 02:06, 7 May 2026
Line 95:		Line 95:
	====With one 5V and one Gnd pin====		====With one 5V and one Gnd pin====
	Minimal variant. But make sure the wires are not too thin, otherwise they may not be able to carry enough current. Recommended wire cross-section: 2.0 mm² or larger.		Minimal variant. But make sure the wires are not too thin, otherwise they may not be able to carry enough current. Recommended wire cross-section: 2.0 mm² or larger.
			<br>
			<pre>5V goes to pin 2.
			Gnd goes to pin 6</pre>
	[[File:Rpi4b-power-1.png\|800px]]		[[File:Rpi4b-power-1.png\|800px]]
	<br>		<br>

2026-05-06T23:04:52Z

Power for Raspberry Pi

← Older revision		Revision as of 02:04, 7 May 2026
Line 86:		Line 86:

	==Power for Raspberry Pi==		==Power for Raspberry Pi==
	For using with DJI Goggles2/3/Integra/N3 Raspberry Pi 4 must be powered ONLY from GPIO or from PoE.		For using with DJI Goggles2/3/Integra/N3 Raspberry Pi 4 must be powered ONLY from GPIO or from PoE adapter.
	<br><br><br>		<br><br><br>

2026-05-06T23:04:43Z

Power for Raspberry Pi

← Older revision		Revision as of 02:04, 7 May 2026
Line 86:		Line 86:

	==Power for Raspberry Pi==		==Power for Raspberry Pi==
	For using with DJI Goggles2/3/Integra/N3 Raspberry Pi 4 must be powered ONLY from GPIO or from PoE ~~or via USB-C port with custom cable~~.		For using with DJI Goggles2/3/Integra/N3 Raspberry Pi 4 must be powered ONLY from GPIO or from PoE.
	<br><br><br>		<br><br><br>